pro tm programmable clock oscillator technical data pro tm s8002 plastic series saronix 141 jefferson drive ? menlo park ca 94025 usa 650-470-7700 800-227-8974 fax 650-462-9894 saronix 5v, hcmos, ttl, smd ds-186 rev c frequency range: description actual size a crystal controlled, hcmos/ttl com- patible oscillator with an internal pro- gramming feature that allows saronix to supply any frequency in the 1 to 125mhz range. this technology significantly re- duces lead-times from weeks to days. the parts are built and stocked un-pro- grammed then programmed by saronix to the frequency required by the cus- tomer before final test and marking. the parts exhibit the same low power, precise rise and fall times, tight symmetry and hcmos/ttl compatible drive capabil- ity as conventional saronix smd oscil- lators. the parts feature tri-state enable or standby control on pin 1. the pack- ages are fully compatible with standard so-j-20 footprints. 1mhz to 125mhz frequency stability: 25*, 50 or 100 ppm over all conditions: calibration tolerance, operating temperature, input voltage change, load change, aging, shock and vibration. temperature range: operating: storage: -20 to +70c or -40 to +85c -55 to +125c supply voltage: recommended operating: +5v 10% supply current: 40ma from 1 to 40mhz, 50ma from 40+ to 125mhz 40ma from 1 to 50mhz, 50ma from 50+ to 125mhz output drive: applications & features quick delivery - days instead of weeks for any frequency - standard or not - between 1 and 125mhz. suited for use with new hcmos mpu's. tri-state output or standby mode high drive hcmos capability stabilities of 25, 50, 100ppm eia standard so-j-20 footprint fully compatible with the epson sg-8002ja series configurations. other saronix products with com- patible electrical and mechanical specifications are available, please see data sheets for the st410h or nth/ntt h. available on tape & reel; 24mm tape, 1000pcs per reel symmetry: -20 to +70c: -40 to +85c: 5ns max 20% to 80% v dd , 0.8 to 2v (ttl) 10% v dd max, 0.5v max (ttl) 90% v dd min, 2.5v min (ttl) 50pf max 1 to 50mhz, 20pf max 50+ to 125mhz or 10 ttl 1 to 40mhz, 5ttl 40+ to 125mhz 40ps max 33+ to 125mhz 100ps max 1 to 33mhz rise & fall times: logic 0: logic 1: load: period jitter rms: mechanical: mil-std-883, method 2002, condition b mil-std-883, method 2003 mil-std-883, method 2004, conditions b2 mil-std-883, method 2007, condition a mil-std-202, method 215 mil-std-202, method 210, condition i or j shock: solderability: terminal strength: vibration: solvent resistance: resistance to soldering heat: environmental: thermal shock: moisture resistance: mil-std-883, method 1011, condition a mil-std-883, method 1004 part numbering guide s8002 h s h b ? 106.25 (t) series saronix programmable oscillator package h = plastic smd, j-lead stability tolerance * a = 25ppm, -20 to +70c b = 50ppm, -20 to +70c c= 100ppm, -20 to +70c e = 50ppm, -40 to +85c f = 100ppm, -40 to +85c p = output enable s = standby frequency example pn: s8002hshb - 106.2500 10ttl/5ttl load: 50pf/20pf load: @ 50% v dd hcmos 1 to 50mhz 45/55% 40/60% @ 50% v dd hcmos 50+ to 125mhz 40/60% 40/60% @ 1.5v ttl 1 to 27mhz 45/55% 40/60% @ 1.5v ttl 27+ to 125mhz 40/60% 40/60% type h = 5v, cmos t = 5v, ttl *25ppm is only available at certain frequencies, please contact saronix. standby current: 50a max (use option s, see part number builder) (t) = tape & reel full reel increments only
all specifications are subject to change without notice. saronix pro tm programmable clock oscillator technical data pro tm s8002 plastic series 141 jefferson drive ? menlo park ca 94025 usa 650-470-7700 800-227-8974 fax 650-462-9894 saronix 5v, hcmos, ttl, smd ds-186 rev c package details, type h tri-state or standby logic table output waveform pin 1 input logic 1 or nc logic 0 or gnd pin 3 output oscillation high impedance/standby required input levels on pin 1: logic 1 = 2.0v min logic 0 = 0.8v max pin 1: tri-state control pin 2: gnd pin 3: output pin 4: +5 vdc pin function: 2.0 .079 8.95 .352 9.80 .386 max 13.0 .512 max 4.7 .185 max 4.10 .161 0.51 .020 5.08 .200 0.15 .006 7.62 .300 0.25 .010 recommended land pattern 2 1 43 2.5 vdc 1.5 vdc 0.5 vdc t f t f t r t r cmos ttl symmetry symmetry gnd v dd logic 0 20% v dd 50% v dd 80% v dd logic 1 * scale: none ( dimensions in ) mm inches * external high frequency power supply decoupling required. 1.78 .070 2.82 .111 12 43 5.08 .200 7.80 .307 saronix yyww 50.0000 mhz s8002hshb tri-state input test point .01f ( note b ) pin 4 pin 3 v cc out oscillator gnd pin 1 pin 2 ma m v m power supply note: a. c l includes probe and fixture capacitance. note: b. an external .01f bypass capacitor close to package ground and v cc pin is required figure 2 - hcmos test circuit, 5v operation note: a. c l includes probe and fixture capacitance. note: b. an external .01f bypass capacitor close to package ground and v cc pin is required figure 1 - ttl test circuit, 5v operation tri-state input power supply ma m v m pin 4 pin 3 v cc out oscillator gnd pin 2 pin 1 .01f ( note b ) test point c l = 15pf ( note a ) mmbd7000 or equiv r l = 390 ? 1 to 40mhz r l = 780 ? 40+ to 125mhz test circuits c l = 50pf, 1 to 50mhz c l = 20pf, 50+ to 125 mhz ( note a ) solder reflow guide preheat 183 10c 4c/sec max reflow 240 max cooling 4c/sec max 1 ? 2 minutes time 10 sec max 150 200 250 temperature ? c
|